Bluetooth audio · OHM BlueZ5

Felis OHM A2DP Fix

An experimental fix for the case where a Bluetooth audio device reconnects successfully, but media audio continues through the phone speaker.

Public Beta 0.3.1 · Unofficial
⚠️ Experimental system modification — install at your own risk.

This RPM replaces an OHM system library at runtime. Incorrect or incompatible modifications can disrupt audio routing, phone calls or system updates. Compatibility is limited to the exact OS versions and stock OHM build listed below. Uninstall before updating Sailfish OS. Not an official Jolla patch.

DeviceJolla Phone 2026
Sailfish OS5.2.0.20 / 5.2.0.22
CPUaarch64
Stock OHM package1.11.0-1.11.1.jolla

Download

Version 0.3.1-1 · RPM package · install only on the supported device and OS.

Download RPM ↓View upstream Pull Request #11 ↗

GitHub release and packaging sources ↗ · Checksums

RPM SHA256

bd8ade5f348e128c0f623ead0945515df048016933a86d363f850ee1b46eb490

Verify the checksum before installation. The installer checks the stock Sailfish OS version and original OHM library hash; it refuses unknown installations.

Installation

Upgrading from 0.3.0? Remove the old package first using sudo pkcon remove felis-ohm-a2dp-fix, then install 0.3.1. In-place upgrades are not supported. If you manually installed a debug library, restore the verified original library first; the installer rejects modified stock files.

Copy the RPM to your phone and run:

sudo pkcon install-local /path/to/felis-ohm-a2dp-fix-0.3.1-1.aarch64.rpm

The package backs up the original OHM library, activates the fix and restarts ohmd.service.

Removal / return to stock

sudo pkcon remove felis-ohm-a2dp-fix

Removal restores the original library and restarts OHM. The 0.3.1 installation/removal/reinstallation cycle has been tested on Jolla Phone 2026 with SFOS 5.2.0.22. The original backup is retained after removal. Restoration refuses unsupported OS versions or native OHM builds and unknown library hashes. Do not remove or change the saved backup while testing.

What does it change?

After a BlueZ device removal, OHM can recreate a Bluetooth device without its UUID information on reconnect. The plugin may then fail to signal the A2DP route. The patch asynchronously retrieves missing org.bluez.Device1 UUIDs and reconciles the connection state.

Only libohm_accessories.so is replaced; the package does not install a different OHM suite.

Testing and known limitations

  • SFOS 5.2.0.22: RPM 0.3.1 tested with Soundcore Liberty 5, including repeated reconnects, routing back to the phone after disconnect, reboot, phone calls, repeated Bluetooth / phone / speaker switching, and music playback after calls.
  • SFOS 5.2.0.20: the same clean library was previously tested in RPM 0.3.0, with Soundcore Liberty 5, Marshall Major IV, APW Boost Ultra and LAMAX Sounder2 Play. The new RPM 0.3.1 itself has not been device-tested on 5.2.0.20.
  • The original routing fault was reproduced on SFOS 5.2.0.22. The stock OHM package version and library hash are identical to 5.2.0.20; the fix library is unchanged in this release.
  • Known APW Boost Ultra issue: immediately after powering on from the charging case, audio may still need one disconnect/reconnect. This is outside the scope of the fix.
  • Testing on other devices and OS versions is not established; do not bypass the version checks.

Please report your device model, Sailfish OS version, exact steps and results in the main community forum topic.

Previous download: 0.3.0-1 for SFOS 5.2.0.20 only. Use 0.3.1 for new installations.

Technical patch and discussion: upstream PR #11 ↗